"use this for a review if you like" Four in one product revue for DIY project.
Needed new TV for back deck purchased TLC 49" Roku Smart TV = $299.99
Wanted to mount it from above purchased Loctec CMI celling TV mount = $37.99
Wanted ability to move for protection when not in use purchased 100PD sliding door Hardware = $32.06
Needed to protect it form weather purchased outdoor TV cover 47" = $25.99
Total project cost $$396.06. project time 2 to 3 hours
# 1. TLC TV, very satisfied, nice unit, good picture, easy to use, great price.
#2. Loctec celling mount. Very satisfied, 360° rotation and much more. I mounted it to wheels of pocket
Door hardware. This allowed it to rotate and roll flat against the wall when not in use.
#3. Johnson Hardware 100PD sliding door Hardware. I mounted the track beneath upper deck with
Screws, attached the wheels to the TV mount. I left the end screw out far enough to keep the
Wheels from rolling out of track, remove screw to take off for winter.
#4. Mount Factory outdoor TV cover 47". It is made to be removed each time you use it, I cut it on each
End and attached velcro so it can be opened the front rolled up and placed on top of TV when
viewing.
SEE VIDEO
ALL PRODUCTS FROM AMAZON

Replaced, not one, but 2 pocket door tracks with this system. Moved into a home that was 40 years old and had the same pocket door tracks. Needless to say, the doors wouldn't stay on the old tracks, making the doors completely useless. These tracks are such an improvement on the old design. There is no flex with the track and no way for the door to fall off the track. Super easy to install, just know you have to cut a hole in your drywall, and remove several pieces of trim from the door frame. My doors work great now, slide smoothly everytime! I would highly recommend this track system to anyone need I g to fix their pocket doors!

Install was easy enough, I'd recommend watching a "how to" video first but other than that this works really well. Smooth rollers, and the door always hangs and slides straight because of the track being two sided. Just take extra care when removing the trim and having a helper at the end to hold the door while I guided the top of the door into the clips was a huge help. It could have been done if I were alone but that part was a lot easier with a helper. The track was about 7" longer than needed but that was an easy hacksaw fix, the track is also a tight fit width wise, but I coaxed it up into place with a rubber mallet and it went in just fine.

Received door hardware as listed (mostly). My set came with the cheaper rollers for a lightweight door. Two of the pictures showed the more expensive ball bearing rollers. I purchased the soft close kit additionally which comes with rollers and door mounts.

The track is extruded aluminum and very sturdy. Pay attention to the instructions as you will likely need to cut it to allow the rollers to be installed. The track design allows for accumulation of dust and dirt away from the rollers giving a long life before accumulation starts causing problems. The screws are gold colored for the silver track.

The rollers that came with the kit have 3 wheels without bearings. Should last OK with a lightweight door. Rollers and hangers I received are gold colored and the screws are zinc plated. Not a problem if you trim the door as instructed to hide the rollers.

The instructions require more than basic knowledge of doors and construction methods. If you are building your own pocket door you should have that knowledge anyway. The videos are helpful, but this kit is designed for making your own pocket door frame or replacing your existing junk hardware.

Overall, I am very satisfied with the purchase. It was less costly for me to order this kit and the soft close/open kits (2 for both) than to piece it together from the manufacturer's or other websites that I could find. I have extra rollers and mounts left over. The 4 star rating is because the carelessness of screws not matching hardware color.

Pictured item parts do not match what I received: door guide was not included and door rollers do not match what is shown. Picture that is shown in description is a plate on the roller assembly that can be directly attached to to the top of the door. The roller assembly I received cannot. It requires a separate door plate that is attached to door that the roller assembly fits into. And I did not receive this other part. Instruction sheet says to call Johnson directly if parts are missing instead of returning. I did. Cost another $3 +$7 for shipping. My fault for not checking contents when received.