Frigidaire GLET1041AS1 Gallery Series
***
NOTE: Disconnect power prior to performing this installation!!!
There are MANY videos all over the web of this installation, so hit your favorite search engine and feast your eyes prior to attempting this if you have low to no experience with this type of work.
***
The product was a perfect fit, direct replacement.
A small set of Channel Lock pliers (#426) made short work of folding over the metal tabs on the terminals after inserting into the ceramic insulator.
Once each terminal is secured, fasten the coils to each respective retainer. This is done with one coil in the middle and two adjacent coils securing spring tension to the plastic retainers.
Once both ends are secure, begin retaining the heating element roughly at the 50% mark and begin working your way, altering sides to distribute "spring" tension of the heating element as you secure it back to the terminal points.
***
If you do not do this, you risk having under tension sections of the element close to the ceramic insulator and the heating element will be "stretched" thin towards the middle or one end (if you went, say clock wise or counter clockwise only)...
The risk can occur where you end up with a "bulged" section of the heating element from under tensioned coils and the heating element _could_ contact the heat shield that is fastened to the drum. This would result in sparks as the AC voltage powering the heating element, potential fire if your dryer is not clean and free of debris once the installation is complete and the unit is plugged in and powered on.
***
At roughly 25% of the cost of the complete assembly, this was a no-brainer since the rest of my assembly was in great shape.
Even if you need a couple of the retaining clips, they are still available, throw in the ceramic insulator and you would still be under 50% of the cost of the complete assembly. So unless your heat shields are destroyed from a dryer fire or you actually need all clips, insulator, element AND the heat sensor, then by all means does it warrant replacing the entire assembly.
***
Do I recommend this product? Absolutely, going this deep, I busted the shop vac out for a severe internal cleaning job & I replaced the drive belt, nylons & felt while I was at it.. With 3x 15min break in cycles under its belt, I now have a new dryer.

The dryer heating element was a perfect fit as a replacement part. A good, cheaper alternative to buying the entire assembly. Supply Edge is a great customer oriented seller, and their ratings show it. The heating element did fail prematurely after only 5 months of moderate use. I contacted supply edge and they shipped me another replacement part next day. Very easy and streamlined process via email. I recommend buying these parts for the value and great customer service.

Our old heating element failed. I "repaired" it a time or two by twisting the broken ends together. That worked for quite a while.

This replacement part was like night and day compared to the 20+ year old original part. It fit perfectly...actually somewhat better than the worn out part that it replaced! (The better springiness of this new coil attached to the ceramic spacers/holders much better than the old element, which always felt like it was ready to fall off.)

I wish I had bought this a few years back when we first had this issue instead of trying to rig a fix for a part that was beyond its service lifetime.

My husband is a doer and a fixer. We tend to like to fix things ourselves and save the money on labor if at all possible. We got this when our dryer stopped heating. Upon opening the dryer up we saw the old heat coil had broken. We replaced the old coil with this new coil. It fit perfect and has been working better than ever. I forgot how nice it is to have a dryer that works properly. My laundry day goes so much quicker! The quality was awesome.

Researched and Developed in New Jersey
Lifetime Warranty on all GARP Products
Used by technicians and Dyers, Includes Warranty Card
Fits OEM Standards! Guaranteed to Exceed OEM Requirements!
Tested by OEM Technicians!

Product Description
GARP products are researched and Developed in New Jersey USA. We provide a Lifetime Warranty on all GARP Products. Our products are trusted and used by technicians and Dyers, Includes Warranty Card. GARP parts fit OEM Standards and are guaranteed to Exceed OEM Requirements! All GARP products are Tested by OEM Technicians! Replacement for 5300622034 Dryer Heater Coil for Frigidaire, Gibson, Kelvinator, Kenmore, Tappan, Westinghouse.

Purchased this as a low cost alternative to buying the original manufacturers part.
The quality of this heating coil appears to bee as good if not better than the original part it replaced.
It has now been in operation almost every day for the past month and a half and we've had no problems at all.

I'd definitely recommend this part to anyone replacing their heating coil - as long as it's the right one for your dryer model of course! :-)
It's a quality part.