HoldRite QuickStand 30 Inch Water Heater Stand, Up to 100 Gallons, Unassembled, 40-S-30-U
Key features
- •WATER HEATER STAND: The Holdrite QuickStand Water Heater Stand safely elevates water heaters and other equipment above the floor to prevent gases and other debris from coming into contact with ignition source
- •WHAT IS INCLUDED: The QuickStand is easy to assemble and includes (2) safety clips and (2) lag bolts; assembled QuickStand measures 30 inches in diameter by 16 inches in height
- •CONSTRUCTION: Made with galvanized steel, this water heater stand is engineered to support water heaters up to 100 gallons
- •VERSATILE: This water stand can be installed on concrete or framed walls; can also support other equipment such as tanks, washers, and boilers
- •CERTIFIED: Water heater stands are compliant with Uniform Plumbing Code and International Plumbing Code requirements
HoldRite QuickStand 30 Inch Water Heater Stand, Up to 100 Gallons, Unassembled, 40-S-30-U
List Price: $222.19$199.97DEALYou Save: $22.22 (10%)
Free shippingFree Returns – 30 daysFree Order CancellationSecure Payment2–3 Days DeliveryGet It June 24, 2026In Stock (1)No marketing spamNo account requiredFulfilment by FedEx / Amazon / UPS / ShipwirePayPal / Card Buyer Protection
Customer Reviews
Reviews sourced from verified Amazon purchasers4.5
out of 5
Based on 10 reviews
5★
70%
4★
30%
3★
0%
2★
0%
1★
0%
HoldRite 24" Water Heater Stand
K. Schneider✓ Verified Purchase•January 4, 2024
I purchased this stand to replace my old one when I replaced my water heater. It was easy to assemble and very sturdy. Although it's not the cheapest option, it's well-made with quality materials and provides good value for my money. I trust HoldRite as a brand and have used their products in the past, so I knew the quality would be up to my standards. Additionally, the edges of the stand are relatively safe from a sharp-edge perspective, which is definitely a plus.
MADE IN USA?
Luis✓ Verified Purchase•December 23, 2023
It is claimed that the product is Made In The USA! I hope this is true! I Love the heavy gauged material and simple design... If it were for me I would boast the sheet metal screws with a sturdy bolt and locknut with spring washers.
I am happy to support our businesses... I will go online to see more about the company and see if they have more products that I can use.
Thank you.
I am happy to support our businesses... I will go online to see more about the company and see if they have more products that I can use.
Thank you.
Very sturdy
damatrixs✓ Verified Purchase•December 23, 2023
Good buy very sturdy
just what I wanted
Paul Madden✓ Verified Purchase•December 15, 2023
I got this not to support a hot water tank but an electric smoker, the height is just what I wanted and it is more than strong enough. Very pleased with my purchase. BTW a cinch to assemble.
Works perfectly.
K. Wetzel✓ Verified Purchase•November 28, 2023
Comes in a simple box, parts aren't secure inside, but don't really need to be. Heavy gauge steel.
I saw some complaints regarding screw holes and hardware, happy to say this was a non issue. Only one hole was slightly out of alignment so I started that screw halfway first, and then the rest. Put all four screws in partway on each leg FIRST. Then tighten. If the screws are slightly crooked at the end, you can keep screwing and they'll flatten out as the table edge is compressed no problem!
This is thick steel, so when the platform is bent at factory, the bends are very slightly not perfect 90 degrees. Maybe closer to 80-85. If I were using a hand tool, like a screwdriver or wrench, it may have been more difficult. I used a Milwaukee drill with a square bit Phillips.
The hardware included extra screws for me.
Works great, happy. Wish it wasn't so pricy, but, what isn't these days?
I saw some complaints regarding screw holes and hardware, happy to say this was a non issue. Only one hole was slightly out of alignment so I started that screw halfway first, and then the rest. Put all four screws in partway on each leg FIRST. Then tighten. If the screws are slightly crooked at the end, you can keep screwing and they'll flatten out as the table edge is compressed no problem!
This is thick steel, so when the platform is bent at factory, the bends are very slightly not perfect 90 degrees. Maybe closer to 80-85. If I were using a hand tool, like a screwdriver or wrench, it may have been more difficult. I used a Milwaukee drill with a square bit Phillips.
The hardware included extra screws for me.
Works great, happy. Wish it wasn't so pricy, but, what isn't these days?
Page 1 of 2
