INNOGLOW Motorcycle Hand Grips 1" Universal Non-Slip Handgrips Handlebar Grips with Throttle Assist Chrome Black Aluminum Rubber for Harley Kawasiki Suzuki Cruisers
Key features
- •Comfortable:No-slip rubber design effectively dampens operating vibration
- •Easy to Install:Easy installation,directly replace your existing hand grips
- •High Quality:High quality aluminum+rubber lining,durable
- •Package Included:A pair of motorcycle hand grips(left and right);instruction manual is not included
- •Note:Please check the handlebar size and detail information carefully before you purchasing
INNOGLOW Motorcycle Hand Grips 1" Universal Non-Slip Handgrips Handlebar Grips with Throttle Assist Chrome Black Aluminum Rubber for Harley Kawasiki Suzuki Cruisers
List Price: $68.08$61.27DEALYou Save: $6.81 (10%)
Free shippingFree Returns – 30 daysFree Order CancellationSecure Payment2–3 Days DeliveryGet It June 25, 2026In Stock (1)No marketing spamNo account requiredFulfilment by FedEx / Amazon / UPS / ShipwirePayPal / Card Buyer Protection
Customer Reviews
Reviews sourced from verified Amazon purchasers3.7
out of 5
Based on 10 reviews
5★
40%
4★
60%
3★
0%
2★
0%
1★
0%
A lot of mixed reviews on there’s
Joseph✓ Verified Purchase•September 14, 2023
The media could not be loaded. Bought these on a limb saw a lot of mix reviews about the glue being terrible and blah blah blah so honest review. Putting the throttle side on the actual grip came off of the tube which I believe they did it for a reason cause without that being separated I'm almost certain that I wouldn't have been able to get the throttle cables on correctly I added some grip glue to both sides and I have 0 issues now after a month or so of riding I will come back and review this because everyone says they don't last so we will see
Hand Grips
Amazon Customer✓ Verified Purchase•August 22, 2023
I would recommend these
Works well and comfortable if properly installed
Lisa E Walsh✓ Verified Purchase•August 7, 2023
Does not fit well in 7/8 handlebars very mch on the loose side. The factory glue on tye throttle tube is junk, just pull the tube out, clean off residual glue and use gorilla glue. Same with the left side. Align them and mark where you want them, spray a mist of water in the grips and coat the handlebars with gorilla glue. Then slide the grips on and wait overnight. I have had them a month and they are working great and holding up just fine. It all starts with a good install
Install carefully, a lot of gorilla glue needed for safe install.
Andrew ✓ Verified Purchase•July 1, 2023
Throttle grip installed fine, at first, but then shifted downward from handle bar while driving.
There is a plastic tube inside the grip and the grip separated from the plastic tube. Could have been a disaster if it came loose during riding. There was remnants of factory glue on the plastic tube, but barely enough to keep the grip in place. I ended up applying gorilla glue to the entire plastic shaft on the throttle side and then slid the grip back on.
The left grip did not fit tight and requires lots of gorilla glue too. Now I think they're safe to ride with. Hopefully I will never going to remove them. That will be a project in its self.
There is a plastic tube inside the grip and the grip separated from the plastic tube. Could have been a disaster if it came loose during riding. There was remnants of factory glue on the plastic tube, but barely enough to keep the grip in place. I ended up applying gorilla glue to the entire plastic shaft on the throttle side and then slid the grip back on.
The left grip did not fit tight and requires lots of gorilla glue too. Now I think they're safe to ride with. Hopefully I will never going to remove them. That will be a project in its self.
Good quality. Grip replacement
Bill wyllia✓ Verified Purchase•June 25, 2023
Replacement. Adaptable.
Page 1 of 2
