2 Pack 3D Printer Glass Print Bed for Ender 3/5 / Pro / 3X - 235 x 235 x 4 mm - 8 Printer Bed Clips Included - Tempered Glass Replacement/Upgrade for Borosilicate Creality Platform - 3D Printing
Key features
- •3D PRINTER PARTS AND ACCESSORIES: This listing is for a 2 pack of 3D Printer Beds made from tempered glass. 8 custom printer bed clips are also included. The 3d printer heatbeds are securely packed in custom foam. This means they won't arrive shattered or cracked.
- •WIDE RANGE OF COMPATIBILITY: These 3D Printer Bed Plates are compatible with Creality Ender-3, Ender-3 Pro, Ender-3X, Ender-5, CR-20, CR-20 Pro, Geeetech A10, and any other 3D printers requiring a 235x235mm print bed..
- •PRINTER BED CLIPS INCLUDED: You will no longer need to use ugly black binder clips. Not only are they poor quality, but they limit the build area. The clips included with this 3D printer surface look great and maximizemaximise your build area.
- •PERFECTLY FLAT 3D PRINTER PLATFORM: Using a rivals inferior quality 3D printer hot bed that isn't perfectly flat can cause adhesion and print quality issues. With our tempered glass sheet you never have to worry about these problems.
- •TEMPERED GLASS PLATE: The tempered glass is of superior quality to typical borosilicate plates provided by our competitors. The tempered glass is totally flat and smooth, with no dips or pits. Tempered glass is more durable and lasts longer than borosilicate, so you need to replace the plates less frequently.
- •Made from high quality tempered glass.
- •Are you looking for an Ender 3 Upgrade? Perfectly fits the Ender 3, Ender 3 Pro, Ender 3X, Ender 5, CR-20, Geeetech A10, and CR-20 Pro at 235 x 235 x 40 mm.
- •Totally flat surface to avoid any adhesion or print quality issues.
- •Packed in custom foam to avoid any damage during delivery.
- •8 custom printer bed clips included.
- •Load the glass plate into the 3D printer base and attach with the silver clips provided.
- •Center both the bed and nozzle.
- •Lower the nozzle until it touches the top of the glass bed.
- •Readjust the Z axis homing switch.
- •Loosen the switches and reposition.
- •Tighten up the switches when correctly aligned.
- •Carry out a print calibration check to re-adjust the bed.
2 Pack 3D Printer Glass Print Bed for Ender 3/5 / Pro / 3X - 235 x 235 x 4 mm - 8 Printer Bed Clips Included - Tempered Glass Replacement/Upgrade for Borosilicate Creality Platform - 3D Printing
List Price: $31.21$28.09DEALYou Save: $3.12 (10%)
Free shippingFree Returns – 30 daysFree Order CancellationSecure Payment2–3 Days DeliveryGet It June 24, 2026In Stock (1)No marketing spamNo account requiredFulfilment by FedEx / Amazon / UPS / ShipwirePayPal / Card Buyer Protection
Customer Reviews
Reviews sourced from verified Amazon purchasers4.4
out of 5
Based on 10 reviews
5★
90%
4★
10%
3★
0%
2★
0%
1★
0%
Very nice glass bed, but adhesion sucks. Use glue sticks!
DaSavageButchR✓ Verified Purchase•November 1, 2023
Well the glass bed is as described and it comes packaged pretty safely, but the adhesion kind of sucks IMO the print will stick on the first layer, but as soon as it gets to around 20 height it starts lifting from the glass bed so I just threw the stock textured bed atop the glass bed and this solved my adhesion issues (I use it to desperate the heat from having high temps (AI: 75+) one thing I will say is that the prints come off so shiny from the glass bed itself (almost like a mirror) so I'm still pleased with the purchase
Very smooth glass print bed
A. Rohde✓ Verified Purchase•October 20, 2023
Bought this after printing PETG melted the plastic sheet over my aluminum bed.
Works good with some surface binder, like watered down elmers glue sticks. I couldn't get spacing right to run without gluesticks, and needing prints out I quit troubleshooting that in the interest of getting project parts.
After 40 prints I can say that I get consistent results that I am happy with. I also like the shiny surface that the bottom of the print receives from the glass bed.
Haven't needed the second table yet, and that's after having one door knob shaped snow scraper print adhere incredibly well and having dropped the glass unexpectedly in the tub when trying to cold shock the print free. Glass is still chip free and has run from room temp to 80°C for 9 prints since.
Works good with some surface binder, like watered down elmers glue sticks. I couldn't get spacing right to run without gluesticks, and needing prints out I quit troubleshooting that in the interest of getting project parts.
After 40 prints I can say that I get consistent results that I am happy with. I also like the shiny surface that the bottom of the print receives from the glass bed.
Haven't needed the second table yet, and that's after having one door knob shaped snow scraper print adhere incredibly well and having dropped the glass unexpectedly in the tub when trying to cold shock the print free. Glass is still chip free and has run from room temp to 80°C for 9 prints since.
Most people will say you need hairspray or glue sticks with this... you DON'T
Sean L. Ryle✓ Verified Purchase•October 7, 2023
Thi si working great for me. it does adhere a little less than the textured one I had from Creality, BUT, I feel it hearts better and I like the smooth finish I get. You will need to tweak your heat settings (I had to go 60 degree bed instead of 50) and for smaller parts, I need to use a brim instead of a askirt, but it's working great. I clean it every 3-4 days just because I don't want dust building up on it. If you have an enclosure, definitely not even that often is needed.
Good value
sir✓ Verified Purchase•September 10, 2023
The adhesion was not great at first. But after some glue it was a little better but it is handy that it comes with clips
Nice and flat.
☆M☆✓ Verified Purchase•September 4, 2023
These are a bargain at $25 for two pieces of flat glass that fit the Ender 3 bed perfectly. I used chemical etching on the surface on one side of the glass to help give it some "tooth" for adhesion. So far it's been working really well. For multiple pieces that require most of the bed surface, I still spray a thin coat of hairspray for piece of mind... considering these are all 8-12 hour prints that have a fine mesh facing. Very difficult prints for a budget machine like the Ender 3 but this glass surface makes it possible. I've been printing PLA at 210° with the bed warmed to 50° and prints stick perfectly. As long as glass cools down, prints pop right off on their own. They key is getting your bed trammed correctly or no amount of glue or hairspray is going to help you. Don't waste your money on overpriced borosilicate glass that chips easily, tempered glass will work just as well, if not better.
Page 1 of 2
