INCRA I-BOX Jig for Box Joints
Key features
- •To get right to the point, the new Incra I-Box is the most advanced tool ever produced
- •Its revolutionary design allows faster setup, greater versatility, and improved user safety compared to traditional jigs
- •At the same time, it's easy to use and the included 1 hour instructional DVD covers everything from basic setup to advanced decorative joinery
- •Use it on your table saw or router table to cut great looking box joints
- •Reversible design works on either side of the cutter
- •Exclusive dual-pitch lead screw mechanism for fast micro-adjusting and a broad 1/8-Inch - 3/4-Inch range of pin widths
INCRA I-BOX Jig for Box Joints
List Price: $317.19$285.47DEALYou Save: $31.72 (10%)
Free shippingFree Returns – 30 daysFree Order CancellationSecure Payment2–3 Days DeliveryGet It June 22, 2026In Stock (5)No marketing spamNo account requiredFulfilment by FedEx / Amazon / UPS / ShipwirePayPal / Card Buyer Protection
Customer Reviews
Reviews sourced from verified Amazon purchasers4.5
out of 5
Based on 10 reviews
5★
80%
4★
20%
3★
0%
2★
0%
1★
0%
Product damage out of box.
former hoser•September 24, 2017
The mauve linoleum is chipped in one area. Its still fully functional but may start chipping more due to its location. Instructions a bit strange to read through and may have worked better in black and white. Ran a few boards through and item works like a charm, watch the enclosed dvd or go to youtube for install and use. I took points off because of the chipped linoleum but other than that a good product.
Edit, I got in touch with Peachtree and showed them the pictures, they agreed to send a replacement part right away. Great customer service in my opinion.
Edit, I got in touch with Peachtree and showed them the pictures, they agreed to send a replacement part right away. Great customer service in my opinion.
Kiss test did not go well for me
Chip•March 14, 2017
Didn't do well on router table, mostly my fault. Must not have followed directions, which resulted in damage to guild plate and broken bit. Incra support is awesome though, sent pictures of damage and they had parts breakdown and directions on how to repair. They suggested that damage would not interfer with setup, we will see. Just bought new table saw will try it there hope I have better luck. Those plates are 20$ a pop plus shipping lol
Assembly Hardware did not Fit tapped holes, Customer Service to the Rescue
Halka•May 30, 2016
I've not been able to use this jig because the assembly hardware provided doesn't even fit into the miter bar. Following step 3 in the assembly instructions, it becomes clear that the #10-24 x 3/8" button head fasteners are too large and do not seem to match the threading of the holes in the miter bar.. They'll go about 3/32" in and then start to strip.
Hoping this 1-star review will prompt some kind on reply from the manufacturer or other customers who've encountered the same issue. Really disappointed thus far :(
UPDATE: Incra responded to my email within a few hours and sent a replacement miter bar and screws over the weekend. Everything fit together perfectly after that, performs as advertised, satisfied customer!
Hoping this 1-star review will prompt some kind on reply from the manufacturer or other customers who've encountered the same issue. Really disappointed thus far :(
UPDATE: Incra responded to my email within a few hours and sent a replacement miter bar and screws over the weekend. Everything fit together perfectly after that, performs as advertised, satisfied customer!
Great new tool!
Thomas F. Wachs•March 14, 2016
Long ago I bought a Leigh Dovetail Jig which I used a few times. It made nice dovetails if I was really careful, but I wasn't always so. I then took an old Incra Jig for crosscutting, and modified it so that I could cut finger joints which I find to be better looking. I pretty much wore it out, so when this box joint jig showed up on line, I jumped on it. I used it to make some large drawers for a cabinet in our summer home. This jig, combined with the Freud 1/4"-3/8" set of finger joint blades made quick work of the construction. I love it!!!
Requires some fine tuning to get the joint to align properly and ...
Lloyd A. Watts•December 13, 2015
Can be a little complicated to use if you only use it occasionally. Requires some fine tuning to get the joint to align properly and is very sensitive to movement of the adjustment knobs. Better have several test pieces available to get the joint right. Once set it is very dependable and fairly easy to use.
Page 1 of 2
