PGFUN CNC 3D Touch Probe Upgraded XYZ Axis Anti-roll Edge Finder Waterproof 3 Coordinate Measuring Sensor Kit with 6mm Shank & Cable, Compatible with Mach3 and Grbl (Probe Tip)
Key features
- •This is the origin 22mm/0.87" tungsten steel probe tip/ stylus for V6 3D touch probe/ edge finder
- •Main Specs: Thread-M2.5 x 4.5mm/ 0.18" (length), Ball Dia: 2mm/ 0.08 in, Total Length: 26.5mm/ 1.04 inch
- •Note: to ensure accuracy, concentricity needs to be adjusted after changing the probe tip every time.
- •Any Question, Free to Contact Us.
BrandPGFUN
CategoryMilling Machines
PGFUN CNC 3D Touch Probe Upgraded XYZ Axis Anti-roll Edge Finder Waterproof 3 Coordinate Measuring Sensor Kit with 6mm Shank & Cable, Compatible with Mach3 and Grbl (Probe Tip)
List Price: $29.08$26.17DEALYou Save: $2.91 (10%)
Free shippingFree Returns – 30 daysFree Order CancellationSecure Payment2–3 Days DeliveryGet It June 23, 2026In Stock (1)No marketing spamNo account requiredFulfilment by FedEx / Amazon / UPS / ShipwirePayPal / Card Buyer Protection
Customer Reviews
Reviews sourced from verified Amazon purchasers4.8
out of 5
Based on 6 reviews
5★
83%
4★
17%
3★
0%
2★
0%
1★
0%
With minimal changes to Universal G Code Sender it works
doc✓ Verified Purchase•July 26, 2023
Don't throw out the paper receipt as its the instructions telling you what color wire is which. Note requires a 5v to 24v power source for the red cable, Black is Ground and Yellow is Signal. Same setup as any powered proximity switch you have to source at least a 5 volt power source for the red cable. Those people that righteously say its a three pin plug (Note you do have to provide your own) without offering jumpering it to a 5 volt pin are not helpful. Very good value as unlike an Aluminum touch plate this is insulated from the machine so if like me you have an aluminum bed this will still be able to align your machine. They also threw in a freebie which I used to test the wires a little wire clamp kit.
Came in faster then it said, works very well, tolerances very good.
Rick K.✓ Verified Purchase•July 12, 2023
It will work with any controller that uses NO, I'm sure they have one that is NC mine can use either so I didn't care which one I ordered.
I did put a resistor just to make sure there was no floating voltage it did work without it also.
Mainly will be used for flatbed correction right now.
I did put a resistor just to make sure there was no floating voltage it did work without it also.
Mainly will be used for flatbed correction right now.
Not great not bad
David J Friedeck✓ Verified Purchase•June 30, 2023
Not as repeatable as I had hoped for. Z axis not really usable.
Im impressed!
ernesto guevara✓ Verified Purchase•May 21, 2023
This exceeded my expectations. Ive boughten some other ones in the past. This is very well machined. Works very well for the precision i need. It has 4 set screws that let you adjust the concentricity unlike other cheaper ones.
I would definitely recommend this seller and this product. We'll just see if it stands the test of time now.
I would definitely recommend this seller and this product. We'll just see if it stands the test of time now.
You are just as accurate as the tools you have
Jono✓ Verified Purchase•May 10, 2023
Needed if you are serious about cnc, if you are not serious and still using a cnc you will still need this.
Page 1 of 2
![RIEDHOFF X-Axis Power Milling Machine, [450 LB Torque ] Power Feed Table Mill,110V, 0-200PRM Adjustable Rotate Speed for Bridgeport and Similar Knee Type Milling Machines](https://m.media-amazon.com/images/I/41UHXMx+9XL._SL500_.jpg)
