We have had thus installed for over a year now. Has worked great with using 4 of the switches currently. The only issue I have had was about 4 months in I lost one of the switch lights. It went out one night and has not worked since. I haven't tried to take it back apart to see what the issue is, everything else works flawlessly.

2014 JK Unlimited Sport (Instagram: @thosesexyassjeeps)

Took a bit of a flyer ordering this aux switch bundle as I was not familiar with Voswitch. I really liked that there are 8 circuits/switches and that with the control unit located under the hood that you do not have to re-open dash panels to wire in new components.

Installation was pretty simple and the single control wire was easy to route at the top of the windshield and down the driver side A-Pilar. Routing through the firewall was easy as the jeep is the automatic, our other jeep is a manual (and a couple years older) and in order to run the wire cleaning I ended up cuttings and then soldering the control wire.

Other than that, the unit fits great and the buttons seem solid, the switch housing and control unit are quality made and look like they will last. Can't wait to add components!

I am not sure why you would pay so much more for SPods when these work just as good. Well implemented and decent instructions to help you get there. I have factory Aux switches in my truck and found these to work in an equivalent manner.

Pros:
You can set to auto shut-off if batt voltage gets too low
make switched or always on
All on/off button for all switches
Dimmable back lighting
Wiring comes complete for this with simple screw on connectors and rings as well as wire loom at proper measure lengths for the given application.
Instructions provide decent directions for firewall passthrough if you review them well.
Wire loom on positive connections.

Cons:
Switches are specific to this application. While it comes with plenty, not every label is a perfect fit and I don't know where to find more of them.
Cutout for the JL makes the bolt on connection very weak and it bends as a result
Cable to switches is pretty thick and requires trim removal and re-installation rather than snaking through. Firewall areas are also limited by the connector.
Having to pick your color of LEDs by SKU is somewhat limiting given how cheap multicolored LEDs are now.
Not sure why negative wire is not in wire loom together with positive wire
No bus bar for negative which is a minor inconvenience.

I really have liked these and the flexibility they provide. They give 30A connections to each switched connection. It does say don't hook up a winch directly to it, because an 10000lb winch would fry it at full load, but you can use it to a larger relay to control the winch so I see why they include the connection. 30A does cause some limitation with other items as well such as Halogen lights as you are limited to pairs of 100W lights, but this is better than many of the competitor products and matches the high end in the market.

The switches are plentiful and work well when lit up off/on. I am not sure where to find more, but other switches that look like them are NOT compatible.
My largest complain as indicated earlier is where the device connects to the footmans loop in the center of the JK. It bends significantly when you connect it. This made me use the screws, double sided tape, and the screws around the footmans loop and they still bent a bit. This is the one thing I think could use improvement on this device. The vendor clearly has listened to the market over the years as many videos online show various generations where improvements have been made to the clasp, enclosure water tightness, and also to the wiring in general. I don't understand why they did not put the positive and negative inside the wire loom rather than keeping negative separate. It makes you have to put additional wire loom on or wrap it around the negative cable. The connectors appear to have been improved as well as water tight connections to the casing from previous generations.

I almost purchased an additional one of these for the driver a pillar, but found out that the connection box under the hood needs to be in the same place. An expansion for those that like accessories would be a nice addition.

Overall i am very happy with this and would purchase it again over many of the competitive products.

The switch panel is amazing, it is high quality and designed perfectly. Installing it easy just make sure you go slow and do it right. Just what I was looking for.

This was by far the best option when choosing between SPOD and Voswitch. I picked this up at $179.90 here on Amazon versus $720 for an SPOD. I had the SPOD on a previous Jeep before Voswitch was available and it was nice, but not worth an extra $540. The Voswitch is just as high in quality as the competitor and the install/fit/finish is nearly identical. There's an install video on YouTube that is helpful to watch before doing the project on your own. It took me two hours to complete and I worked slow, taking my time to zip tie everything nice and orderly.

The kit comes with all of the parts you will need, zip ties, lots of rocker switch cover options, and an extra 100 amp inline fuse. Each circuit has 30 amp fuses pre-installed, however you may want to swap these out based on what you will be connecting to the Voswitch.

You might ask yourself if you really need an 8 switch/relay system? Yes! You do if you are going to mod your jeep with extra electronics. For example, mine is setup for CB Radio, Air Compressor, Winch Solenoid, Front Lights, Rear Lights, Rock Lights, Front Locker, and Rear Locker.