Best case design I've ever worked with! Very well thought out design and quality construction.
Easy to install components with plenty of room for everything including air!

Got this in June 2023, but it took a couple of months to get the build squared away.

Package arrived safe and sound, and was very well packaged with plenty of crumple room to protect the tempered glass (as one would expect with a Corsair product).

Top-front I/O cables, two 140mm front intake fans, rear 140mm exhaust fan, and sata powered fan controller were all pre-installed with cables nicely routed inside the back cabinet area. Hook and loop straps already in place and keeping everything tight and tidy.

Both the front and back panels are pin-hinged and can be easily removed by loosening the screw on the top hinge and just lifting the panel up (when it's fully open). Inner cabinet in back also has an additional door, but your wiring will need to be very neat and flat if you expect that inner door to stay shut on its own (mag latch). Fortunately, the outer panel snaps into the case strong enough to keep it all contained.

Case is quite large and rather heavy (roughly 50 lbs with glass panel installed), so that might be something to consider when placing it on a desk / table, or if planning on relocating the pc often.

While the case can supposedly hold two 420mm rads plus an additional 360mm (or 480mm) rad in the motherboard tray area, I don't see how it could work without interference happening as the 360 spot is located near the front of the pc). Since the MB tray area needs to have both the fans and the rad completely inside the case, that will most certainly hit a front mounted rad (480/420/360 that's also inside the case).

I just went with a top mounted 420mm rad, a 360mm rad in MB tray, and used the front area for fans. Easy and plenty of room for related hardware. An alternative would be a top 420, a front 420 (or 480) and use the MB tray spot for 3 or 4 120mm fans.

Side-by-side sata racks inside the power supply shroud (configuration as shipped) would make for a tight spot to work in, but as I'm not spinning rust, removing a single thumb screw on each rack allowed me to just delete them from the build altogether. It's possible to put them in bottom front area, so there's several config options available. There are also 5 SSD spots (two rear cabinet area, three on top of p/s shroud) for even more storage if needed.

There's two different plastic shrouds for dealing with the area in front of the power supply shroud, but they're kind of fiddly to deal with and decidedly an area that I feel quality of materials is lacking. I just deleted them as they're non-critical.

Still putting finishing touches on build, but overall I'd say this is one of the easiest cases I've worked in over the last 20 years or so. If you're doing a lot of tear-downs and generally moving the case around a lot, the weight does get to be noticable (aluminum cases are almost worth the extra coin when you're flipping it around a lot), but overall this is a solid case at a reasonable price. Hard to fault it really, just remember to lift with your knees.

I have experience with both the 5000D and this case, 7000D. I have built similar systems with both. The 5000D would be my minimum case size to balance airflow and space. For my personal build, I need more room for expansion and I like to just have alot of space.

This is a HEAVY case with very minimal places where you can get a good grip. The case itself alone is probably 50lbs. Then fully loaded you're pushing 75lbs. It's very sturdy and built like a tank. The side panels are thick. I believe the glass is 1mm thicker than that of the 5000D (in which there been cases of where 5000D glass sides are shattering). Everything in the 7000D is similar to the 5000D but just bigger and roomier. I have an Intel 13900KF + RTX 4090 (beast card) with plenty of room to spare. I added a couple of extra fans to keep the rig as cool as possible. I'm running air cooled with Noctua DH-15S. You can easily fit Corsair's largest AIO coolers. I had considered this but didn't want to deal with leaks and other issues. If you wanted to, you can load this up with 10-11 case fans. There's that much space. I like the magnetic dust screens. There's not a whole lot of plastic pieces, which is why it's so heavy. Plenty of space for the RTX 4090. Cable management in the back is ok. There's primarily one main channel that's used and it's already housing alot of just the case cables. If you start adding the PSU cables, you'll find the channel gets thick such that the inner door won't shut. It does have other channels that you can use but because the case is so big, unless your cables are custom and extra long, you'll end up routing via shortest distance. Cable management on the front side is ok. There are shrouds in place but I had to remove one because it caused too much bend in the motherboard cable if used. The grommet holes are ok. Would like to see some larger grommet holes at the top and bottom. Accessories are kinda bare minimum and comes in a cardboard box. Not like some other case vendors where you get a nice plastic case. Not a big deal. Lots of space for external drives (which is one reason why I got it) - (2-4) SSDs + (6) 3.5HDD cages. The cages are metal but drive brackets are plastic with no rubber vibration dampeners. So there will be noise. I like how there's plenty of USB3.0 A and C front panel connectors. Minimal lighting (got the non-RGB one). But the big selling feature is the amount of airflow you can get through this case. Because of the larger fans and airflow, the case is super quiet for me and my idle temps are pretty low. Overall, I like the case. Is it the best? I think there are better (Be Quiet! Dark Base 901 or Cooler Master Cosmos) but they were also more expensive. I didn't want to spend too much on a case and this was already pushing it. For the balance of build, features, and price it worked for me. Lastly, the internals have some nice configurability options that should suit anyone's needs for extra fans or more minimalist look or expansion of room.

Anyone thinking about getting the Corsair SHIFT series PSUs, there's plenty of space for the side mounted cabling. For rear mounted PSUs, there's room if you remove one of the 3.5" HDD drive cages.

If you plan to vertically mount GPU (I didn't), I believe there is enough room between the glass side panel and the GPU for decent airflow. It's much more space than the 5000D. I wouldn't even consider vertically mounting GPU in the 5000D. The 7000D will work though. This case did come with an anti-sag mount for the GPU which is nice.

It's came pretty stingy with only 3 fans - 2 front and 1 back. But I guess most people get their own fans. I just added two 140mm to get 3 fans in front, 1 on top, and 1 in back. I may add more fans on the top if there's a need. I did not bother adding fans to the side panel - you can literally go crazy with too many fans.

The bottom feet on the case are kinda stubby and low. My case is on low pile carpet, so there isn't alot of space for PSU to get good airflow. But I think my PSU fan runs in quiet mode. I do wish case manufacturers think about this. You can probably put this case on the table BUT it's BIG.. may over power your desk setup.

Because it's so heavy, it will be challenging to move around. I have thought of getting a wheeled platform to put the case on because of this. This could be an issue so you may want to consider something lighter or smaller.

It's a very good case, I put a asus z790-h and an intel 13900ks in it. Lots of room. Only two complaints, firstly the door does not close on mine unless you pull it up slightly like its slightly unaligned, not a huge deal but for the price it should not happen. Two, it would be nice if you could remove the PSU shroud, some people (like me) don't care about nice looking interiors and just want the most cable freedom. In this case the PSU shroud seems fused into the case. As it is now, the cables to my motherboard from my PSU are pulled tightly through the case access holes and it makes me slightly uncomfortable. No other complaints, all the buttons worked, the USB front headers worked, and it seems high quality aside from the door issue, and is very nice looking.

This is huge, it's massive and has some decent weight to it. This case is excellent for anyone with the funds too, it is sleek in design adaptable to any setup tons of space. Once you read the manual and watch a few videos on how to set up the case it's fairly simple. Unfortunately I don't have any videos of me setting up the case. All screws were present when item arrived and when the build was done she was quite as a mouse. I was able to overclock the build and wasn't even able to hear the sound of the fans and the easy access glass door is a nice touch to. If I get another chance I will make a video showing off the case. In conclusion this case is amazing and I love it even though it was for a customer. Hopefully this review will help you make a concise decision, have a beautiful day thank you ðŸ' namaste!