I love the finished look--the only problem so far is my lack of skills. While removing the masking tape, I pulled off some paint. However, there was plenty of paint left so I was able to do touch-ups.

My shower/bath looks amazing after using this product. I believe my tub was the original from when the house was built in 1975 and the tub looked dingy and had terrible soap scum (which you must scrape off before using this product). The second picture is after one coat of paint, which I decided to use a paint sprayer for and smoothed out using the foam roller. It had decent coverage but I think the sprayer tends to use more paint and I was unable to get a full coat with the first tub. I had to purchase a second tub of paint and ended up just using the roller and was able to cover the whole bathtub with only half the amount of paint. As far as durability, time will tell. But as you can see in the 3rd picture, it was already scraping off. I waited a full week to use the bathtub or put water on it. My son uses a bath chair and it got pushed into the edge of the tub and caused the paint to smush up. I was able to scrape it off and sand it down a bit and repaint it and so far it has been okay.
If the kit had some type of epoxy or harder finish to go over it, I think that it would last forever but for now I am just very careful not to use anything that could cause the paint to scrape up in the bathtub.

I had been putting up with the hideous "greige" tiles, sink, and fiberglass shower enclosure ever since we bought our house. After loads of research, I decided to try DWIL tub and tile paint. I don't have a fan in my bathroom, and everything I read about all the alternatives out there (including the one that gets the most hype: rustolem's tub refinishing paint) were epoxy based, and you had to have major respirator masks to use safely. When I found DWIL, I thought it might be too good to be true, so I decided to try it on the sink first and see how it went, and then decide if I'd do the tile, the floor, and the shower enclosure.

Well, not only did it work, but it was almost easy. I mean, sure, I had to take time to tape everything off, and clean things well, but "¦ that stuff is amazing. It took more coats than I expected to not see a little of the greige showing through, but the paint dried so quickly, I was able to go over areas with show-through within an hour of doing a coat. And if I dribbled paint on the floor (which I did a couple times), a wet rag would bring that up easily if it was still wet, or it would scrape off with a scrape razor. No problem.)

The sink came out so well, I did the walls and floor and the shower enclosure. My entire bathroom looks completely different. I wound up redoing the ancient 80s wall tiles in the other full and half bath in the house.

The shower enclosure took a lot longer, and a lot more coats were needed (I think I did 5), but again, it's fast applying and drying, so it wasn't that bad.

I recommend buying better rollers - the ones that come in the kit aren't great, but the paint brush that comes with it is fine. The hardening liquid that comes in the kit isn't in a great container; I immediately transferred it to a small glass jar and would put the paint into a plastic paint jug so I could do smaller sections instead of prepping the whole can at once. (It's possible to use the paint you've pre-prepped hours after without it hardening: just cover it tightly - the paint brush and roller too - with plastic wrap.)

After the DWIL had fully cured, I painted the shower and sink with two coats of polycrylic to give it a bit more shine, but it's not necessary. The walls and floor didn't get the polycrylic addition, and they look fabulous too.

We're not planning to sell our house any time soon, but I know the investment of time and energy I made in refreshing our bathrooms with the help of DWIL paint will pay off big-time. They look modern and clean, instead of dull, old, and greige. A (relatively) easy and definitely affordable DIY project that anyone can do.

We used this product to paint the tile floor in our bathroom. We ordered the white paint, and it took around three coats to get the right coverage. However it was easy to use and dried surprisingly quick - although we followed the directions and stayed off of it for the allotted time. Overall we are happy - and this is more affordable than buying new floors for us.

This is extremely low VOC! I had my n95 prepared for the smell, but didn't need it. I did 3 coats. The pictures show progression of before, first coat, second coat, third coat. I suggest if you have tile- cut in the grout then roll. It makes it much easier for subsequent coats. These 3 coats took a little over 1 container to complete. 1 container completed 2 coats and this is a large bathtub. It cures enough in 2 hours that you can step on it without doing any damage. I wore socks just to ensure I wasn't introducing any dirt. I did pre sand before the first coat using 180p and cleaned with a mold/mildew remover and wiped down with water. Looks great, great product so far- but my back is killing me- not the fault of the paint. Dries hard.